Total 50 results found for the keyword of "eos section 11 6 ethernet configuration commands"
...
show traffic-engineering database
Use the show traffic-engineering database to display the topology used for CSPF computations. Starting from eos Release 4.23.1F, the SRLG group details of a neighbor ...
Sample configurations
EVPN VXLAN IRB Sample configuration
In the topology below, we are connecting a Layer 2 site with a Layer 3 site using Layer 3
EVPN (type-5 route). Right side leaves are MLAG ...
EVPN and VCS commands
Global configuration Mode
router
general
Router BGP configuration Mode
next-hop
resolution disabled
redistribute
service vxlan
route-target
route-target
export
route-target ...
... in the
eos 4.26.0F for VXLAN, singe-active is
another mode of operation in which only one PE per VLAN accepts traffic for
that ethernet segment.
Single-active multihoming is useful for:
Manually controlled ...
VXLAN commands
VXLAN Global configuration
commands
interface vxlan
ip address virtual
vxlan vni notation
dotted
VXLAN Interface configuration
commands
vxlan flood vtep
vxlan multicast-group ...
ethernet VPN (EVPN)
This chapter describes Arista’s EVPN implementation. sections in this chapter
include:
EVPN Overview
EVPN Layer
3 Core Operations
Integrated Routing and Bridging
VPN MPLS
Transport ...
... (eos release
4.25.2F)
Support of 400GBASE-ZR with Open Forward Error Correction (O-FEC) (eos release
4.25.2F)
Override a transceiver slot’s maximum power limit (eos release
4.25.2F)
Platform Compatibility ...
Environment commands
Environment Control
configuration commands
environment fan-speed
environment insufficient-fans action
environment overheat action
locator-led
Environment Display
commands ...
Precision Time Protocol (PTP) commands
PTP commands
ptp announce interval
ptp announce timeout
ptp delay-mechanism
ptp delay-req interval
ptp domain
ptp enable
ptp forward-v1
ptp hold-ptp-time ...
... command replaces the EOS CLI prompt with an SQLite
prompt.switch# event-monitor interact
sqlite>
This command exits SQLite and returns to the EOS CLI
prompt.sqlite> .quit
switch#
event-monitor ...
Session Management commands
Global configuration commands
configure replace
configure session
management api eos-sdk-rpc
management api external-services
management api gnmi
management api gnsi ...
... like Signal-To-Noise Ratio, Residual Inter Symbol Interference, PAM4 Level
Transition Parameters, etc. that such optics support.
With Performance Monitoring feature eos collects and maintains certain ...
...
Drop count
Device ID
Egress interface
FCS type
Reserved
TAP Aggregation Extra MPLS Pop (4 to 6 Labels)
Available starting with eos Release 4.23.1F extra MPLS pop for TAP Aggregation ...
Latency Analyzer (LANZ)
Arista Networks’ Latency
Analyzer (LANZ) is a family of eos features that provide enhanced visibility
into network dynamics, particularly in areas related to the delay packets
experience ...
... displays
information about the active flows maintained in the eos.
Command Mode
EXEC
Command Syntax
show flow tracking sampled flow-table [
detail | dst-ip |
dst-port | group |
interface | protocol ...
... rates also decrease the amount of processing
time available for other eos applications.
With hardware acceleration, all sFlow processing is done in hardware
using specialized chips, called accelerators. ...
... can request or change. The agent gathers data from the MIB and responds to requests for information. For a list of supported MIBs, refer to the release notes for the specific eos version.
This chapter ...
VM Tracer
This chapter describes VM Tracer configuration and usage and contains these sections:
VM Tracer Introduction
VM Tracer Description
VM Tracer configuration Procedures
VM Tracer commands ...
... leaks in eos or customer user processes.
Process leaks to too many processes or scripts running at one time.
Over configuration of the system requiring more memory than available.
Large number of temporary ...
...
Starting in Release eos 4.23.1, ingress on inner IP header matching
in MPLS packets is also supported on PBR ACLs. In order to enable this, the following must
be configured in a user-defined TCAM profile: ...