- Written by Ankit Gupta
- Posted on 2月 2, 2022
- Updated on 2月 2, 2022
- 7325 Views
When a CVP cluster is deployed in a different location from the devices under management, it is possible that it
- Written by Ravi Krishnamurthy
- Posted on 6月 5, 2023
- Updated on 6月 5, 2023
- 5303 Views
DPS (Dynamic Path Selection) provides the ability to select different paths for different types of traffic to optimize application performance.
- Written by Krzysztof Gongolewski
- Posted on 9月 11, 2022
- Updated on 8月 30, 2024
- 7133 Views
Dynamic NAT connection limit is a feature which allows to limit the number of dynamic NAT connections.
- Written by Eric He
- Posted on 2月 7, 2024
- Updated on 2月 7, 2024
- 3268 Views
This feature extends the capabilities of event monitor to include NAT logging. The tracked events are NAT translations creations, NAT translations updates, NAT translations deletions and NAT translations deletion reasons (aging deletion, aging deletion(hw not programmed), peer deletion)
- Written by Thomas Altenburger
- Posted on 1月 20, 2022
- Updated on 8月 27, 2024
- 9333 Views
NAT (Network Address Translation) is a feature that allows each packet's addresses to be rewritten according to the user configuration. The packet qualification happens within the ingress pipeline of the forwarding plane, then the egress pipeline uses a shared table memory to decide which fields to adapt.
- Written by Freedom Garcia
- Posted on 12月 24, 2024
- Updated on 12月 24, 2024
- 24 Views
This feature, when enabled, allows NAT to function on traffic traversing between VRFs, over inter-VRF static routes or routes leaked to VRFs other than where they were configured.
- Written by Indu Mahadevan
- Posted on 12月 24, 2024
- Updated on 12月 24, 2024
- 22 Views
Support for IPSec connections in a full-cone Network/Port Address Translation (NAT) environment has been added to the Dynamic Path Selection (DPS) setup. DPS optimizes application performance by selecting different paths for various types of traffic. In this configuration, STUN is used to discover the translated IP address of WAN interfaces and export it to BGP.
- Written by Shyam Kota
- Posted on 6月 20, 2022
- Updated on 6月 30, 2022
- 6932 Views
The NAT Flow feature is an unusual NAT feature that allows the translation of traffic streams in ways that go beyond the typical translations achieved with NAT. In that sense, the feature is not strictly a standard NAT feature; it can be seen as a combination of NAT and DirectFlow.
- Written by Wojciech Franczyk
- Posted on 11月 6, 2023
- Updated on 11月 7, 2023
- 3867 Views
The ICMP protocol has a type of messages used to handle problematic situations in a network, like for example destination unreachable, packet's Time To Live exceeded, and others. They all contain the "original datagram" field which represents the leading octets of the datagram to which the ICMP message is a response. The original datagram consists of the IP header + at least 64 bits of the data.
- Written by Jikai Yin
- Posted on 6月 29, 2016
- Updated on 12月 11, 2023
- 9384 Views
NAT Peer State Synchronization feature provides redundancy and resiliency for Dynamic NAT across a pair of devices in an attempt to mitigate the risk of single NAT device failure. Each switch advertises connection state updates to its peer. State update consists of connection creation, connection state change (TCP mostly) or connection tear down
- Written by Freedom Garcia
- Posted on 11月 5, 2021
- Updated on 8月 30, 2024
- 7719 Views
Non default VRF support is now available for Static unicast NAT. Twice NAT. Dynamic NAT. VRF support
- Written by Prashanth Krishnamurthy
- Posted on 3月 7, 2024
- Updated on 3月 8, 2024
- 3259 Views
This feature allows the packets to be VxLAN encapsulated after NAT translation, Reverse NAT translation applied on VxLAN tunnel terminated packets
- Written by Haomin
- Posted on 4月 12, 2024
- Updated on 4月 12, 2024
- 2368 Views
Some configurations in NAT may have some trade-offs and even cause problems. The Show Configuration Consistency NAT CLI can check these configurations, and provide hints to change the configuration or the trade-offs to be considered.
- Written by Ram Murthy
- Posted on 3月 3, 2023
- Updated on 8月 27, 2024
- 7287 Views
NAT has been supported in DCS-7150 for many years. Starting at EOS 4.21.6F, NAT functionality is supported on certain 7050X3 platforms.
- Written by Corentin Le Bigot
- Posted on 9月 5, 2021
- Updated on 8月 29, 2024
- 7440 Views
Hardware accelerated NAT for transit fragmented traffic is enabled by default. It’s important to note that
- Written by Nik Zaborovskii
- Posted on 12月 8, 2020
- Updated on 12月 12, 2024
- 10250 Views
Multicast NAT is a feature that performs NAT translations on multicast traffic. It can be configured under SVIs,
- Written by Gokul Unnikrishnan
- Posted on 3月 3, 2023
- Updated on 1月 30, 2024
- 4886 Views
This feature allows for the configuration of password requirements when creating or modifying local user accounts. Specifically, policies can necessitate that passwords meet the following requirements:
- Written by Brett Hatch
- Posted on 6月 5, 2020
- Updated on 8月 30, 2024
- 8312 Views
Static NAT rules may optionally include an access list to filter the packets to be translated.