Total 42 results found for the keyword of "eos section 2 5 session management commands"
session management commands
Global Configuration commands
commit timer
configure replace
configure session
management api eos-sdk-rpc
management api external-services
management api gnmi
management ...
...
Examples
In this example, eos sends hello messages to all known neighbors every
10 seconds. If the switch does not receive
hello responsesfrom a neighbor for 4*10=40 seconds, the switch loses
communication ...
... SR
Policy IdentificationThe following identifies an SR
policy.
Endpoint - An IPv4 or IPv6 address which
refers to the destination of the policy. eos
allows 0/0 and 0:: and calls these IP addresses
null ...
...
Note: In eos releases prior to 4.23.2, this command identified system peers
with IPv6 addresses by their reference IDs (the first four octets of the MD5 hash of
the IPv6 address). In later releases, ...
Connection management
The switch supports three connection methods:
Console
SSH
Telnet
The switch always enables the console and SSH. By default, eos disables Telnet.
management commands place ...
Configuration sessions Overview
The configure
session command creates a configuration session for CLI
commands and ends it after issuing the commit command. Each
configure session has a unique name. ...
...
sFlow exports packet samples and topology meta data to a centralized collector
application.
sFlow scales and operates on all switch ports simultaneously.
eos implements sFlow on all switches, without ...
... manager can request or change. The agent gathers data from the MIB and responds to requests for information. For a list of supported MIBs, refer to the release notes for the specific eos version.
This ...
VM Tracer
This chapter describes VM Tracer configuration and usage and contains these sections:
Introducing VM Tracer
VM Tracer Description
VM Tracer Configuration Procedures
VM Tracer commands ...
... can be enabled or disabled on the
fly without impacting regular packet forwarding functionality.
NDR Switch Sensor Extension
NDR switch sensor extends eos telemetry for network threat detection. The ...
RSVP-TE LSR
RSVP-TE applies the Resource Reservation Protocol (RSVP) for Traffic Engineering (TE) to distribute MPLS labels for steering traffic and reserving bandwidth.
The eos implementation supports ...
... timestamp
Drop count
Device ID
Egress
interface
FCS type
Reserved
TAP Aggregation Extra MPLS Pop (4 to 6 Labels)
Available starting with eos Release 4.23.1F extra MPLS pop for TAP
Aggregation ...
... a GRE tunnel, the payload of the outgoing GRE packet contains the payload of
the incoming source packet starting from the MPLS header. eos
strips L2 and outer L3 headers from the mirror copy. When the
MPLS ...
Multicast Source Discovery Protocol (MSDP)
Multicast Source Discovery
Protocol (MSDP) describes a topology that connects multiple IPv4 Protocol
Independent Multicast Sparse-Mode (PIM-SM) domains. ...
... area
and interface levels.
Note: On the same area or interface, eos allows security configuration with either AH or ESP but not
both. We can have one area or interface configured with AH and
another ...
... in
section 2.1.1.2 of RFC8667.
The following enhancements are available by release:
eos Release 4.22.1F adds support for TI-LFA backup paths that protect IS-IS SR labeled traffic corresponding to a ...
... This allows eos to direct specific services over the specified RIB domains, overriding the default behavior. Further, this feature, through the use of user-defined tunnel RIBs, empowers an administrator ...
... offers an echo function. eos supports
asynchronous mode and the echo function.
Asynchronous Mode
Demand Mode
Asynchronous Mode
In asynchronous mode, BFD control packets are exchanged by neighboring ...
... Beginning with eos Release 4.25.0F, MLDv2 snooping is supported on MLAG deployments.
Limitations
The extraneous “Switch” interface should be ignored in show mld
snooping counters and show mld snooping
counters ...
... OSPFv2 adjacencies with DR Other neighbors.
OSPFv2 Multiple Instances Support
eos Release 4.22.1F adds support for multiple OSPFv2 instances to
be configured in the default VRF. OSPFv2 Multiple Instances ...