Total 33 results found for the keyword of "eos section 6 5 event monitor"
event monitor
The event monitor writes system
event records to local files for access by SQLite database commands.
Note:
Beginning with release eos-4.20.5F, event-monitor is not enabled by default.
Use ...
... the metrics with threshold values configured on the switch when
enabled. eos enables PTP monitoring by default.
Enabling and Disabling PTP monitoring
Use the ptp monitor command to
enable PTP monitoring ...
Logging of event Notifications
Arista switches log event notifications using the Syslog protocol. By default, event
notifications are logged internally to /var/log/messages, but they can also be displayed
on ...
...
Drop count
Device ID
Egress interface
FCS type
Reserved
TAP Aggregation Extra MPLS Pop (4 to 6 Labels)
Available starting with eos Release 4.23.1F extra MPLS pop for TAP Aggregation ...
Latency Analyzer (LANZ)
Arista Networks’ Latency Analyzer (LANZ) is a family of eos features that provide enhanced
visibility into network dynamics, particularly in areas related to the delay packets
experience ...
... displays
information about the active flows maintained in the eos.
Command Mode
EXEC
Command Syntax
show flow tracking sampled flow-table [
detail | dst-ip |
dst-port | group |
interface | protocol ...
...
sFlow exports packet samples and topology meta data to a centralized collector
application.
sFlow scales and operates on all switch ports simultaneously.
eos implements sFlow on all switches, without ...
... can request or change. The agent gathers data from the MIB and responds to requests for information. For a list of supported MIBs, refer to the release notes for the specific eos version.
This chapter ...
VM Tracer
This chapter describes VM Tracer configuration and usage and contains these sections:
Introducing VM Tracer
VM Tracer Description
VM Tracer Configuration Procedures
VM Tracer ...
... This means the directly connected
TaskTracker nodes can belong to different clusters. eos supports a maximum of five
clusters per switch.
MapReduce Tracer Configuration
The MapReduce Tracer structures ...
...
show traffic-engineering database
Use the show traffic-engineering database to display the topology used for CSPF computations. Starting from eos Release 4.23.1F, the SRLG group details of a neighbor ...
BGP PIC Edge for EVPN VXLAN Routes for Remote VTEP Failures
When a remote VTEP goes down, the IGP and BGP must recompute a new best path
traffic destined to affected BGP prefixes originally reachable ...
IGMP and IGMP Snooping
IGMP Snooping
IGMP Host Proxy
Description
Supported Features
IGMP Protocols
Configuring IGMP
Configuring IGMP Snooping
IGMP Host Proxy
IGMP and IGMP Snooping
Commands ...
... for OSPFv2 adjacencies with DR Other neighbors.
OSPFv2 Multiple Instances Support
eos Release 4.22.1F adds support for multiple OSPFv2 instances to
be configured in the default VRF. OSPFv2 Multiple ...
...
Note: Unlike node segments, anycast segments do not have the ‘N’ flag set described in section 2.1.1.2 of RFC8667.
The following enhancements are available by release:
eos Release 4.22.1F adds support ...
... hop resolution semantics of BGP routes with an ordered list, or profile, of resolution RIB domains (for example, either tunnel or IP domain). This allows eos to direct specific services over the specified ...
...
Maintenance Mode Configuration
Maintenance Mode Commands
Overview
Using maintenance mode, you can perform several maintenance activities such as:
eos image upgrade.
Initial configuration or ...
... and destination
addresses..
ACLs can also be made dynamic (not persisting in the eos), and the
payload keyword can be used to
turn an ACL into a User-Defined Field (UDF) alias for use in other ACLs. ...
...
Configuring Priority-Flow-Control (PFC)
Configuring PFC Watchdog
DCBX and Flow Control Commands
Introduction
eos implements Link Layer Discovery
Protocol (LLDP) and the Data Center Bridging ...
... IP addresses that match a route in the routing table. When a switch receives a proxy ARP request, eos performs a check to send the response immediately or delay the response based on the configured maximum ...