Overview

The following topics are covered in this section:

  • Scope
  • Receiving and Inspecting the Equipment
  • Installation Process
  • Safety Information
  • Obtaining Technical Assistance
  • Specifications

    The Arista 7060X and 7260X Series are a range of 1RU and 2RU high performance 25G, 40G, 100G and 400G high density, fixed configuration, data center switches with wire speed layer 2 and layer 3 features, and advanced features for software driven cloud networking. The Arista 7060X and 7260X deliver a rich choice of interface speed and density allowing networks to seamlessly evolve from 10G/40G to 25G/100G and 200G/400G. With support for advanced EOS features these switches are ideal for large scale cloud, traditional and fully virtualized data centers. The Arista 7060SX2-48YC6 and 7060CX2-32S provide support for IEEE 25GbE and support a shared packet buffer pool of 22 MB with a consistent low latency of 450ns.

Scope

This guide is intended for properly trained service personnel and technicians who need to install the following Arista Networks Data Center Switches:

DCS-7060CX-32S DCS-7060CX2-32S DCS-7060SX2-48YC6
DCS7060PX4-32 DCS7060DX4-32 DCS-7060DX4-32S

 

Important: Only qualified personnel should install, service, or replace this equipment.

Seul le personnel qualifié doit installer, service, ou remplacer cet équipement.

 

Receiving and Inspecting the Equipment

Upon receiving the switch, inspect the shipping boxes and record any external damage. Retain packing materials if you suspect that part of the shipment is damaged; the carrier may need to inspect them.

If the boxes were not damaged in transit, unpack them carefully. Ensure that you do not discard any accessories that may be packaged in the same box as the main unit.

Inspect the packing list and confirm that you received all listed items. Compare the packing list with your purchase order. Parts List provides a list of components included with the switch.

Installation Process

The following tasks are required to install and use the switch:
  1. Select and prepare the installation site (Site Selection).
  2. Assemble the installation tools listed (Tools and Parts Required for Installation).
  3. Attach the mounting brackets and install the switch in an equipment rack (Rack Mounting the Switch).
  4. Connect the switch to the power source and network devices (Cabling the Switch).
  5. Configure the switch (Configuring the Switch).
    Important: Class 1 Laser Product: This product has provisions to install Class 1 laser transceivers which provide optical coupling to the communication network. Once a Class 1 laser product is installed, the equipment is a Class 1 Laser Product. The customer is responsible for selecting and installing the Class 1 laser transceiver and for insuring that the Class 1 AEL (Allowable Emission Limit) per EN/IEC 60825, CSA E60825-1, and Code of Federal Regulations 21 CFR 1040 is not exceeded after the laser transceiver have been installed. Do not install laser products whose class rating is greater than 1. Refer to all safety instructions that accompanied the transceiver prior to installation. Only Class 1 laser devices, certified for use in the country of installation by the cognizant agency are to be utilized in this product.

     

    Produit Laser de classe 1: Ce produit a des dispositions pour installer des émetteurs-récepteurs de laser de classe 1 qui offre de couplage au réseau de communication optique.Une fois un produit laser de classe 1 est installé, l'équipement est un produit Laser de classe 1 (Appareil à Laser de Classe 1).Le client est responsable pour sélectionner et installer l'émetteur/récepteur de laser de classe 1 et pour assurer que la classe 1 AEL (limite d'émission admissible) par EN/IEC 6-825, CSA E60825-1, et Code des règlements fédéraux 21 CFR 1040 ne soit pas dépassée après avoir installé l'émetteur/récepteur de laser. Ne pas installer des appareils à laser dont la cote de classe est supérieure à 1.Voir toutes les consignes de sécurité qui ont accompagné l'émetteur-récepteur avant l'installation. Seuls appareils laser de classe 1 certifiés pour une utilisation dans le pays d’installation par l’organisme compétent doivent être utilisées dans ce produit.Ultimate disposal of this product should be in accordance with all applicable laws and regulations.

     

    Important: Ultimate disposal of this product should be handled in accordance with all national laws and regulations.

     

    L'élimination finale de ce produit doit être effectuée conformément à toutes les lois nationales et règlements.

Obtaining Technical Assistance

Any customer, partner, reseller or distributor holding a valid Arista Service Contract can obtain technical support in any of the following ways:

  • Email: このメールアドレスはスパムボットから保護されています。閲覧するにはJavaScriptを有効にする必要があります。. This is the easiest way to create a new service request.

    Include a detailed description of the problem and the output of “show tech-support”.

  • Web: https://www.arista.com/en/support.

    A support case may be created through the support portal on our website. You may also download the most current software and documentation, as well as view FAQs, Knowledge Base articles, Security Advisories, and Field Notices.

  • Phone:+1 866-476-0000 or +1 408-547-5502.

     

    Important: No user serviceable parts inside. Refer all servicing to qualified service personnel.

    Aucune pièce réparable par l'utilisateur à l'intérieur. Confiez toute réparation à un technicien qualifié.

     

Specifications

Table 1. Switch Specifications (Dimensions and Weights)
Switch Size (W x H x D) Weight
DCS-7060CX-32S 48.3 x 4.4 x 40.6 cm (19 x 1.75 x 16 inches) 9.5 kg (21.0 lbs.)
DCS-7060CX2-32S 48.3 x 4.4 x 40.6 cm (19 x 1.75 x 16 inches) 9.5 kg (21.0 lbs.)
DCS-7060SX2-48YC6 48.3 x 4.4 x 40.6 cm (19 x 1.75 x 16 inches) 8.8 kg (19.4 lbs.)
DCS-7060PX4-32 48.3 x 4.4 x 67.0 cm (19 x 1.75 x 26.4 inches) 9.5 kg (21.0 lbs.)
DCS-7060DX4-32 48.3 x 4.4 x 67.0 cm (19 x 1.75 x 26.4 inches) 9.5 kg (21.0 lbs.)
DCS-7060DX4-32S 44.0 x 4.4 x 54.6 cm (19 x 1.75 x 21.5 inches) 10.5 kg (23.0 lbs.)

 

Table 2. Switch Specifications (Operational and Storage)
Switch Operating Temperature Storage Temperature Operating Altitude Relative Humidity
All 0° to 40°C

(32° to 104°F)

 -25° to 70°C

(-13° to 158°F)

 0 to 3,000 meters

(0 to 10,000 feet)

 5 to 90%

(non-condensing)

 

Table 3. Switch Specifications (Power Input)
Power Source PSU Models Ratings
Power Input (AC Power) PWR-500AC 100 - 240 VAC, 6.5 to 3.0 A, 50/60 Hz
Power Input (DC Power) PWR-500-DC -48 to -60 VDC, 15 A
Power Input (AC Power) PWR-1611-AC-RED 200 - 240 VAC, 11.2 to 9.5 A, 50/60 Hz

 

Table 4. Switch Specifications (Power Draw)
Switch Power Draw (Typical / Maximum) Supported Power Supply
DCS-7060CX-32S 220 W / 410 W PWR-500AC

PWR-500-DC
DCS-7060CX2-32S 220 W / 410 W PWR-500AC

PWR-500-DC
DCS-7060SX2-48YC6 240 W / 385 W PWR-500AC

PWR-500-DC
DCS-7060PX4-32 640 W / 915 W PWR-1611-AC-RED
DCS-7060DX4-32 690 W / 980 W PWR-1611-AC-RED