Overview

This Quick Start Guide (QSG) describes the CCA-ETM-Q12 appliance.

This chapter contains the following topics:

Scope

 

This guide is intended for properly trained service personnel and technicians who need to install the following Arista appliance:

This guide is covers the CCA-ETM-Q12 appliance.

Important:

Only qualified personnel should install, service, or replace this equipment.

Seul le personnel qualifié doit installer, service, ou remplacer cet équipement.

Receiving and Inspecting the Equipment

Upon receiving the appliance, inspect the shipping boxes and record any external damage. Retain packing materials if you suspect that part of the shipment is damaged; the carrier may need to inspect them.

If the boxes were not damaged in transit, unpack them carefully. Ensure that you do not discard any accessories that may be packaged in the same box as the main unit.

Inspect the packing list and confirm that you received all listed items. Compare the packing list with your purchase order. The Parts List provides a list of components included with the appliance.

Installation Process

The following tasks are required to install and use the appliance:
  1. Select and prepare the installation site (Site Selection).
  2. Assemble the installation tools listed (Tools Required for Installation).
  3. Install the appliance (Mounting the Appliance).
  4. Connect the device to the power source and network appliances (Cabling the Appliance).
  5. Configure the appliance (Configuring the Appliance).
    Important:

    Class 1 Laser Product: This product has provisions to install Class 1 laser transceivers which provide optical coupling to the communication network. Once a Class 1 laser product is installed, the equipment is a Class 1 Laser Product. The customer is responsible for selecting and installing the Class 1 laser transceiver and for insuring that the Class 1 AEL (Allowable Emission Limit) per EN/IEC 60825, CSA E60825-1, and Code of Federal Regulations 21 CFR 1040 is not exceeded after the laser transceiver have been installed. Do not install laser products whose class rating is greater than 1. Refer to all safety instructions that accompanied the transceiver prior to installation. Only Class 1 laser devices, certified for use in the country of installation by the cognizant agency are to be utilized in this product.

    Produit Laser de classe 1: Ce produit a des dispositions pour installer des émetteurs-récepteurs de laser de classe 1 qui offre de couplage au réseau de communication optique.Une fois un produit laser de classe 1 est installé, l'équipement est un produit Laser de classe 1 (Appareil à Laser de Classe 1).Le client est responsable pour sélectionner et installer l'émetteur/récepteur de laser de classe 1 et pour assurer que la classe 1 AEL (limite d'émission admissible) par EN/IEC 6-825, CSA E60825-1, et Code des règlements fédéraux 21 CFR 1040 ne soit pas dépassée après avoir installé l'émetteur/récepteur de laser. Ne pas installer des appareils à laser dont la cote de classe est supérieure à 1.Voir toutes les consignes de sécurité qui ont accompagné l'émetteur-récepteur avant l'installation. Seuls appareils laser de classe 1 certifiés pour une utilisation dans le pays d’installation par l’organisme compétent doivent être utilisées dans ce produit.

    Important:

    Ultimate disposal of this product should be handled in accordance with all national laws and regulations.

    Aucune pièce réparable par l'utilisateur à l'intérieur. Confiez toute réparation à un technicien qualifié.

Obtaining Technical Assistance

Any customer, partner, reseller, or distributor holding a valid Arista Service Contract can obtain technical support in any of the following ways:

Specifications

This section lists the specifications of the CCA-ETM-Q12.

Table 1. Appliance Specifications (Dimensions and Weights)
Appliance Size (W x D x H) Weight
CCA-ETM-Q12 438mm x 429mm x 44mm 6.4 kg

 

Table 2. Appliance Specifications (Operational and Storage)
Appliance Operating Temperature & Humidity Storage Temperature & Humidity Operating Altitude
CCA-ETM-Q12 0 to 40°C

20% - 80%

 -10 to 70°C

5 to 95% RH @ 55°C

 0 to 2000 meters

 

Table 3. Appliance Specifications (Power Input)
Power Source (PSU) Rating
250W 100-240V