Print

Wi-Fi Access Point O-435E - Access Point Overview Print

Access Point Overview

O-435E is a multi-radio 802.11be (Wi-Fi 7) access point. Refer to the datasheet for more information.

Note: This equipment is suitable for use in environment air spaces (plenums).
This chapter provides an overview of the access point (AP) and describes the following:

Front Panel

The front panel of the AP has 6 LEDs indicating the status of AP functions.

Figure 1. Front Panel LED
Image showing the LEDs at the front panel of the access point
Table 1. Labels: Front Panel LEDs
Label Description
1 Power
2 2.4 GHz Radio
3 5 GHz Radio
4 6 GHz Radio
5 LAN1 PoE PD
6 LAN2 PoE PSE (802.3af)

Power LED

The following table describes the Power LED states:

Table 2. Power LED States Description
  Green Red
Solid Running at full capability Running at reduced capability.
Blinking Received an IP address, but not connected to the server. Did not receive an IP address.

Reduced capability indicates that the AP receives lower than the required maximum power from the PoE++ switch. It means the AP receives 802.3at instead of 802.3bt.

LAN1 LED -ON when the corresponding interface up.

LAN2 LED - ON when the corresponding interface up, and either wired guest or link aggregation configured.

Radio LEDs: ON when the corresponding radio operational.

Side Panel - Left

The side panel of the AP has a reset pinhole and console port.

Figure 2. Side Panel
Table 3. Labels: Side Panel
Label Description
1, 2, 3 Antenna Port for 2.4/5/6 GHz. The AP has three (3) antenna ports on the left and right side of the AP.
3 Reset pin
4 Console
Port Description Connector Type Speed/Protocol
Console

Establish a ‘config shell’ terminal session through a serial connection.

 RJ-45
  • RS 232 Serial (115200 bits per second)
  • Data bits:8
  • Stop bits: 1
  • Parity: None
  • Flow Control: None
Reset

Reset to factory default settings port. Hold down and power cycle the device to reset.

 Pinhole push button N/A

When you reset the AP, the following settings also change:

  • The Config shell password resets to config.
  • Server discovery value erases and changes to the default, redirector.online.spectraguard.net (primary) and wifi-security-server (secondary).
  • The AP loses all the VLAN configurations.
  • If the AP has a static IP configured, the reset erases the IP address and the AP sets to DHCP mode with the factory default IP address of 169.254.11.74.

Bottom Panel

The bottom panel of the AP has two ports, LAN1 and LAN2. Connect a wired LAN from a switch or a hub to the LAN1/PoE++ port of the AP to power on the AP. The LAN1 port supports the 802.3bt power standard. Use an active wrench to open the LAN cap. The LAN cap has a width of27 mm. LAN2 acts as a PoE Power Sourcing Equipment (PSE) that provides power to any devices connected through LAN2. You cannot use LAN2 to provide power to the AP.

Figure 3. Rear Panel
Table 4. Labels - Ports
Label Description
1 Kensington lock
2 LAN2 (PoE PSE)
3 LAN1 (PoE+ PD)
Table 5. Port Details
Port Description Connector Type Speed/Protocol
LAN 1 5Gbps Ethernet with 802.3bt compliant PoE PD. RJ-45 10M/100M/1000Mbps/2.5G/5Gbps Ethernet
LAN 2 5Gbps Ethernet with 802.3af compliant PoE PSE. RJ-45 10M/100M/1000Mbps/2.5G/5Gbps Ethernet
..