Overview

This guide is intended for network professionals who need to install the Arista 7200 S-Series ZTX MSS Appliance.

The section reviews the following topics:

Scope

This section lists the covered devices in this guide:

  • ZTX-7250S-16S-F
CAUTION: Only qualified or trained personnel should install, service, or replace this equipment.

Seul le personnel qualifié doit installer, service, ou remplacer cet équipement.

Receiving and Inspecting the Equipment

 

Upon receiving the device, inspect the packaging and record if there is any external damage. Retain the packing material if you suspect any part of the shipment is damaged; the carrier might need the packing material to inspect.

If the packaging is not damaged during transit, unpack each box carefully. Ensure that all accessories are packed in the same box as the device.

Review the packing list that comes with the networking device to assure you have received all the items listed. Refer to the Parts List to verify that all components are present.

Installation Process

 

This section describes the steps for installing and using the ZTX MSS Appliance in a Campus or Data Center environment.
  1. Select and prepare the installation site. (Site Selection)
  2. Assemble the installation tools listed. (Tools and Parts Required for Installation)
  3. Attach the mounting brackets and install the device in an equipment rack. (Rack Mounting the Device)
  4. Connect the device to the power source, console cables, and management network. (Cable the Device)
  5. Configure the ZTX MSS Appliance. (Configuring the Device)

Safety Information

Refer to the Arista Networks document. Safety Information and Translated Safety Warnings are available at https://www.arista.com/en/support/product-documentation.

Important:

Class 1 laser product: This product has provisions for installing Class 1 laser transceivers that provide optical coupling to the communication network. After installing a Class 1 laser product, the equipment is now a Class 1 laser product. The customer is responsible for selecting and installing the Class 1 laser transceiver and for ensuring that the Class 1 AEL (allowable emission limit) per EN/IEC 60825, CSA E60825-1, and Code of Federal Regulations 21 CFR 1040 is not exceeded after the laser transceiver has been installed. Do not install laser products whose class rating is greater than 1. Refer to all safety instructions that accompany the transceiver before installation. Only Class 1 laser devices certified for use in the country of installation by the cognizant agencies are to be utilized in this product. The ultimate disposal of this product should be by all applicable laws and regulations.

Produit laser de classe 1: Ce produit a des dispositions pour installer des émetteurs-récepteurs de laser de classe 1 qui offre de couplage au réseau de communication optique. Une fois un produit laser de classe 1 est installé, l'équipement est un produit laser de classe 1 (Appareil à laser de Classe 1). Le client est responsable pour sélectionner et installer l'émetteur/récepteur de laser de classe 1 et pour assurer que la classe 1 AEL (limite d'émission admissible) par EN/IEC 6-825, CSA E60825-1, et Code des règlements fédéraux 21 CFR 1040 ne soit pas dépassée après avoir installé l'émetteur/récepteur de laser. Ne pas installer des appareils à laser dont la cote de classe est supérieure à 1.Voir toutes les consignes de sécurité qui ont accompagné l'émetteur-récepteur avant l'installation. Seuls appareils laser de classe 1 certifiés pour une utilisation dans le pays d’installation par l’organisme compétent doivent être utilisées dans ce produit.

 

Important:

DO NOT open the device case. There are NO user-serviceable parts inside. Entrust any repair to a qualified technician.

N’ouvrez PAS le boîtier du appareil. Il n’y a AUCUNE pièce réparable par l’utilisateur à l’intérieur. Confiez toute réparation à un technicien qualifié.

Obtaining Technical Assistance

Any customer, partner, reseller, or distributor holding a valid Arista Service Contract can obtain technical support in any of the following ways:

  • Email: このメールアドレスはスパムボットから保護されています。閲覧するにはJavaScriptを有効にする必要があります。

    Include a detailed problem description and the “show tech-support” output.

     

  • Web: https://www.arista.com/en/support

    The support portal on our website allows you to create support cases. You can also download the most current software and documentation and view FAQs, Knowledge Base articles, Security Advisories, and Field Notices.

     

  • Phone: +1 866-476-0000 or +1 408-547-5502

Specifications

This section lists the specifications of the Arista 7200 S-Series ZTX MSS Appliance.

Table 1. Dimensions and Weights
MSS Appliance Size (W x H x D) Weight

ZTX-7250S-16S-F

 17.32 x 3.46 x 20.47 inches

(440 x 88 x 520 mm)

 29.98 lbs

(13.6 kg)

 

 

Table 2. Operating and Storage Temperature
MSS Appliance Operating Temperature Storage Temperature Operating Altitude Relative Humidity

ZTX-7250S-16S-F

 32° to 104°F

(0° to 40°C)

 -13° to 158°F

(-25° to 70°C)

 0 to 10,000 feet

(0 to 3048 meters)

 5 to 95%

(non-condensing)

 

 

Table 3. Power Input
MSS Appliance Power Source Input Power Rating

ZTX-7250S-16S-F

 AC Power 100-240VAC, 10-5A, 50/60 Hz

 

 

Table 4. Power Draw
MSS Appliance Power Draw (Typical/Maximum) Supported Power Supply

ZTX-7250S-16S-F

 200W/750W PWR-861-AC-RED

 

 

Table 5. System Configurations
MSS Appliance Airflow Power Supply Fan Fan Type

ZTX-7250S-16S-F

 Front to rear 2 3+1 FAN-7202-RED