Tag :: 4.20.1F

This features enables ARPs learnt on an SVI interface to be converted into Host routes which can further be

Support for asset tagging aids hardware identification by the use of user supplied strings. Fixed

This feature detects whether a given EOS image is MLAG ISSU compatible with the currently running version on a switch.

BFD for static routes enables monitoring of directly connected next hop reachability using a BFD session. This is

This document describes BFD RFC7130 mode on EOS. RFC7130 defines a mechanism to run BFD protocol over port channels with an independent asynchronous BFD session on every port channel member link. With RFC7130 support, the port channel member link will be removed from forwarding if the BFD session state transitions from UP to DOWN on the member link. This is useful for quickly detecting failures where L1 stays connected but the interface is unable to forward traffic.

The aggregate address advertise only feature adds the capability of NOT installing the Null0 route in the FIB/kernel

BGP Monitoring Protocol (BMP) [1] allows a monitoring station to connect to a router and collect all of the BGP

Nexthop Groups allow users to manually configure a set of nexthops by specifying their nexthop addresses and

This feature adds support for a 'match route type' route map match clause in release 4.20.1F. This clause allows

Bidirectional PIM has information on Bidirectional Protocol Independent Mulicast (PIM). Additional information

Connectivity Fault Management (CFM) is used in Virtual Bridged Local Area Networks for detecting, isolating, and

Config checkpoint mechanism provides a shortcut to copy the current running config into a file stored in checkpoint

Connectivity Monitor is an EOS feature that allows users to monitor their network resources from their Arista switches. The resources being monitored may or may not be Arista devices. Connectivity monitoring is unidirectional in nature.

DHCPv6 Prefix Delegation support enables a DHCP relay agent to program routes for addresses assigned by a DHCP server. The assigned prefixes could either be DHCPv6 IA_PD prefix delegation addresses, or DHCPv6 IA_NA global /128 addresses.

This feature allows eAPI to run in multiple non default VRFs on the same physical router. In this way, users can

EOS 4.20.1F introduces expanded VRRP, VARP and MLAG Peer Gateway virtual MAC capabilities on the 7500R, 7280R,

Ethernet VPN (EVPN) is an extension of the BGP protocol introducing a new address family: L2VPN (address family

MPLSoGRE Filtered Mirroring is a specialized version of Mirroring to GRE Tunnel and Filtered Mirroring in which

Hardware Table Capacity Monitoring is a new feature to keep track of the capacity and utilization of various hardware forwarding resources and generate alerts/syslogs when the utilization exceeds a threshold value. Users can keep track of the current usage statistics using a single show command, and also configure thresholds on a per-resource basis, to be notified about any high-utilization upfront, before reaching any resource limits. The Main use-case would be for troubleshooting in overflow situations and avoid overflows altogether by taking corrective actions on high utilization.

Hierarchical Forwarding Equivalence Class (HFEC) changes a FEC from a single flat level to a multi level FEC

The IPv6 Neighbor Discovery protocol performs Neighbor Unreachability Detection (NUD) in order to determine if two

IPv6 Router Advertisement Consistency Logging, when enabled, allows for notification through syslogging of

IS IS Graceful Restart adds support for Restart Signaling for IS IS, IETF RFC 5306. When IS IS is used

This feature is available when configuring BGP in the multi agent routing protocol model. Ethernet

L3 interface ingress counters can be used to count routable traffic coming into the box on sub interfaces and vlan

LANZ on 7160S 32CQ, 7160 48YC6 and 7160 48TC6 adds support for monitoring congestion on front panel ports with Start,

The LDP pseudowire feature provides support for emulating Ethernet connections over a Multiprotocol Label

Link Fault Signalling (LFS) is a mechanism by which remote link faults are asserted over a link experiencing

Classification of MPLS packets based on traffic class bits in MPLS header for QoS Policy Maps. DCS

The feature MP BGP Multicast provides a way to populate the MRIB (Multicast Routing Information Base). MRIB is an

EOS 4.15.0F adds support for MPLS encapsulation of IP packets in EOS. The functionality is exposed through two

Multi hop BFD  allows for liveness detection between systems whose path may consist of multiple hops. With an

Multicast Only Fast Reroute (MoFRR) is a feature based on PIM sparse mode (PIM SM) protocol to minimize packet loss in a

 . These are the release notes and configuration guide for the OpenConfig feature available in the 4.20.1F EOS

EOS release 4.20.1F adds OSPFv3 flood pacing support that allows configuring the minimum interval between the

Traffic is managed through policy maps that apply data shaping methods to specific data streams. A policy map is a data

The BGP labeled unicast (LU) RFC is used to advertise BGP routes with a stack of MPLS labels, thereby allowing

Multi Agent, Platform independent. This feature supports RFC 7606, which  provides improved security and

Hardware Table Capacity Monitoring is an existing feature to keep track of the capacity and utilization of various

This article describes the Tap Aggregation Traffic Steering on MPLS Labels feature. The purpose of this feature is to

This document describes the truncation capability for Tap Aggregation, which allows tapped traffic to be truncated to a smaller size before being transmitted.

This article describes the TAP Aggregation User Defined Fields feature. The purpose of the User Defined

The BGP labeled unicast (LU) RFC is used to advertise BGP routes with a stack of MPLS labels, thereby allowing

Unidirectional links is a feature that configures an Ethernet interface transmit and receive paths to be

This feature adds the capability to import as path access-list from a URL, in release 4.20.1F. The file specified by the URL can contain one or more as-path access-list entries. All the entries that are in the file are added to the as-path access-list being configured. This feature gives the advantage of using one EOS CLI command to configure many as-path access-list entries, instead of adding each one of them line by line in the CLI.