Overview

 

Awake Network Security Platform through its subsidiary, Awake Security. The AI-based software platform operates on a physical appliance or a set of physical and virtual appliances. The hardware can be purchased with a Stock Keeping Unit (SKU) having the Data Center Automation (DCA) prefix in the format of DCA-NDR-XY, where X is A (All-in-One), NB (Nucleus), or S (Sensor) and Y is a number indicating a maximum Gb/s rate (currently 100MB, 1GB, 5GB, or 10GB).

Each appliance type has unique characteristics, so identify the correct appliance (All-in-one, Nucleus, or Sensor) for the function before beginning the installation tasks.

Scope

 

This guide is intended for properly trained service personnel and technicians who need to install and configure the Awake Security appliances with the following SKU format:
  • DCA-NDR-S100MB, 1RU Sensor Appliance
  • DCA-NDR-S1, 1RU Sensor Appliance
  • DCA-NDR-S5, 2RU Sensor Appliance
  • DCA-NDR-S10, 2RU Sensor Appliance
  • DCA-NDR-NB10, 2RU Nucleus Appliance
  • DCA-NDR-A5, 2RU All-in-One Appliance

 

Note:

Only qualified personnel should install, service, or replace this equipment.

 

Seul le personnel qualifié doit installer, service, ou remplacer cet équipement.

 

Receiving and Inspecting the Equipment

 

Upon receiving the Awake Security appliance(s), inspect the shipping boxes and record any external damage. If you suspect that part of the shipment is damaged, retain packing materials; the carrier may need to inspect them.

If the boxes were not damaged in transit, unpack them carefully. Do not discard any accessories that may have been packaged in the same box as the main unit.

Inspect the packing list and confirm that you received all listed items. Compare the packing list with your purchase order. Appendix B provides a list of components included with the Awake Security appliance.

Installation Process

 

The following tasks are required to install and use the Awake Security appliance:
  1. Select and prepare the installation site (Section 2.1).
  2. Assemble the installation tools (Section 2.2).
  3. Attach the mounting brackets and install the Awake Security appliance in an equipment rack (Chapter 3).
  4. Connect the Awake Security appliance to the power source and network devices (Chapter 4).
  5. Configure the Awake Security appliance (Chapter 5).
    Note:

    Class 1 Laser Product: This product has provisions to install Class 1 laser transceivers which provide optical coupling to the communication network. Once a Class 1 laser product is installed, the equipment is a Class 1 Laser Product (Appareil à Laser de Classe 1). The customer is responsible for selecting and installing the Class 1 laser transceiver and for insuring that the Class 1 AEL (Allowable Emission Limit) per EN/IEC 60825, CSA E60825-1, and Code of Federal Regulations 21 CFR 1040 is not exceeded after the laser transceiver have been installed. Do not install laser products whose class rating is greater than 1. Refer to all safety instructions that accompanied the transceiver prior to installation. Only Class 1 laser devices, certified for use in the country of installation by the cognizant agency are to be utilized in this product.

     

    Produit Laser de classe 1: Ce produit a des dispositions pour installer des émetteurs-récepteurs de laser de classe 1 qui offre de couplage au réseau de communication optique.Une fois un produit laser de classe 1 est installé, l'équipement est un produit Laser de classe 1 (Appareil à Laser de Classe 1).Le client est responsable pour sélectionner et installer l'émetteur/récepteur de laser de classe 1 et pour assurer que la classe 1 AEL (limite d'émission admissible) par EN/IEC 6-825, CSA E60825-1, et Code des règlements fédéraux 21 CFR 1040 ne soit pas dépassée après avoir installé l'émetteur/récepteur de laser. Ne pas installer des appareils à laser dont la cote de classe est supérieure à 1.Voir toutes les consignes de sécurité qui ont accompagné l'émetteur-récepteur avant l'installation. Seuls appareils laser de classe 1 certifiés pour une utilisation dans le pays d’installation par l’organisme compétent doivent être utilisées dans ce produit.Ultimate disposal of this product should be in accordance with all applicable laws and regulations.

     

    Note:

    Ultimate disposal of this product should be handled in accordance with all national laws and regulations.

     

    Aucune pièce réparable par l'utilisateur à l'intérieur. Confiez toute réparation à un technicien qualifié.

     

Obtaining Technical Assistance

 

Any customer, partner, reseller or distributor holding a valid Arista Service Contract can obtain technical support in any of the following ways:

  • Email: 이 이메일 주소가 스팸봇으로부터 보호됩니다. 확인하려면 자바스크립트 활성화가 필요합니다..

    This is the easiest way to create a new service request. Include a detailed description of the problem.

     

  • Web: https://www.arista.com/en/support

    A support case can be created through the support portal on our website. You can also download the most current software and documentation, as well as view FAQs, Knowledge Base articles, Security Advisories, and Field Notices.

     

  • Phone: +1 866-476-0000 or +1 408-547-5502.

     

Note:

No user serviceable parts inside. Refer all servicing to qualified service personnel.

 

Aucune pièce réparable par l'utilisateur à l'intérieur. Confiez toute réparation à un technicien qualifié.

 

Specifications

 

Table 1. Awake Security appliance Specifications (RUs, Dimensions, and Weight)
Awake Security appliance SKU Rack Units (RUs) Dimensions (W x H x D) Weight
DCA-NDR-S100MB 1 43.7 x 4.3 x 65.0 cm

(17.2 x 1.7 x 25.6 in)

20.87 kg

(46 lbs.)

DCA-NDR-S1 1 43.7 x 4.3 x 65.0 cm

(17.2 x 1.7 x 25.6 in)

20.87 kg

(46 lbs.)

DCA-NDR-S5 2 43.7 x 89.0 x 72.3 cm

(17.2 x 3.5 x 28.5 in)

32.7 kg

(72.0 lbs.)

DCA-NDR-S10 2 43.7 x 89.0 x 72.3 cm

(17.2 x 3.5 x 28.5 in)

32.7 kg

(72.0 lbs.)

DCA-NDR-NB10 2 43.7 x 89.0 x 72.3 cm

(17.2 x 3.5 x 28.5 in)

32.7 kg

(72.0 lbs.)

DCA-NDR-A5 2 43.7 x 89.0 x 72.3 cm

(17.2 x 3.5 x 28.5 in)

32.7 kg

(72.0 lbs.)