Cabling the Modular Switch

Cabling the Power Supplies

Before you begin, refer to the Arista Networks document Compliance and Safety Guide available at: https://www.arista.com/en/support/product-documentation.

Important: Power down the switch: Remove all power cords from the power inlets.

 

Mettez le commutateur: Retirez tous les cordons d'alimentation des prises d'alimentation.

 

Important: Installation of this equipment must comply with local and national electrical codes. If necessary, consult with the appropriate regulatory agencies and inspection authorities to ensure compliance.

 

Installation de cet équipement doit être conformes aux codes électriques locaux et nationaux. Si nécessaire, consulter les organismes de réglementation appropriés et des autorités de contrôle pour assurer la conformité.

 

Note: Many configurations will require additional power supplies.

 

Nombreuses configurations exigera des alimentations supplémentaires.

 

Important: Read all installation instructions before connecting the system to the power source.

 

Lire toutes les instructions d'installation avant de brancher le système à la source d'alimentation.

 

Table 2 shows the minimum number of operating power supplies that must be connected to active circuits for each switch to operate.

Each power supply includes a fan that maintains proper power supply temperature. The appendices display the location of components for all switches described in this guide.

Cabling Chassis Ground

Figure 1 and Figure 2 display the location of the chassis grounding locations on the front panel of the switches. Chassis ground locations are also located on the rear panel of the switch chassis (Rear Panel). After mounting the switch into the rack, connect at least one of the chassis grounds to the data center ground using two-hole ground lugs with 16 mm (5/8 in.) spacing, and two M4 x 0.7 screws. After the switch is grounded, ESD wrist straps can be grounded by connecting them to one of the attach points.

Important: Grounding wires and grounding lugs are not supplied. Wire size should meet local and national installation requirements. Commercially available 2 or 4 AWG wire is recommended for installations in the U.S.

À la terre et de mise à la terre fils cosses ne sont pas fournis. Calibre des fils doit satisfaire des exigences de l'installation locale et nationale. Disponible dans le commerce 2 ou 4 AWG fil est recommandé pour les installations aux États-Unis.

 

Important: This equipment must be grounded. Never defeat the ground conductor. This unit requires over-current protection.

 

Cet équipement doit être mis à la terre. Ne jamais modifier le conducteur de terre. Cet appareil nécessite de protection contre les surintensités.

 

Important: Secondary Grounding wires, lugs, and screws (M4 x 0.7) are not supplied.

 

Secondaire à la terre, câbles, cosses et vis (M4 x 0.7) ne sont pas fournis.

 

Figure 1. Chassis Ground Locations (CCS-755)

1 Grounding locations 3 Line cards
2 ESD attach point 4 Supervisor modules
Figure 2. Chassis Ground Locations (CCS-758)

1 Grounding locations 3 Line cards
2 ESD attach point 4 Supervisor modules

To power down the switch,remove all power cords from the power inlets.

Cabling the AC Power Supplies

The switches use PWR-3351-AC-RED (Figure 3) AC power supplies. Power cables are included with the accessory kit (Table 1). To power the switch, connect the cables to the C20 connectors on the PSU inputs, and insert the other side of the cables into the main power providing circuit(s).

 

Note: The power supply, handle color, orientation, etc. may be different in your device from the one shown in Figure 3.

 

Figure 3. AC Power Supply (PWR-3351-AC-RED)

Rear Panel displays the rear panel location of the power supplies.

 

Note: After disconnection from main power, LED(s) on the PSU remain on for a short period of time. The actual duration varies for each PSU model, but the LED(s) will eventually turn off. The PSU fan will ramp up and run at maximum speed for a few seconds before shutting down.

 

Power Supply Specifications

Table 1 shows the power supply specifications for each of the PSUs supported.

Table 1. Power Supply Specifications (each PSU)
Power Supply Maximum Output Power Rating (DC) Input Voltage and Frequency Maximum Input Current Input Branch Circuit Protection
PWR-3351-AC-RED 1400 W 3000 W 3300 W 100 to 127 VAC 200 to 220 VAC 220 to 240 VAC 50/60 Hz 16 A 20 A

 

Important: Each power supply requires input branch circuit protection in compliance with AHJ requirements.

 

Chaque alimentation nécessite une protection du circuit de la branche d’entrée conformément aux exigences de l’AHJ.

 

Power Supply Configurations

Table 2 shows the power supply configurations for the modular switches.

 

Note: PSU input voltage for all PSUs in the system must be the same.

 

Table 2. Power Supply Configurations
Modular Switch Recommended Number of PSUs (for redundancy) Minimum Number of PSUs Required Maximum Number of PSUs Supported
CCS-755 3 1 6
CCS-758 5 1 10

Recommendations for Power Supply Usage

  • Use separate circuits (A & B) with required protection for each power supply.
  • Use the same PSU model when replacing a failed PSU. Any suitable alternative must be approved before using if the original model is no longer supported or available.
  • Unless your switch allows for mixing power supplies, do not mix power supply types.
  • Populate the PSU slots sequentially.
  • Valid redundancy configurations for each domain are described in Power Supply Redundancy section.

Power Supply Redundancy

Important: Installation of this equipment must comply with local and national electrical codes. If necessary, consult with the appropriate regulatory agencies and inspection authorities to ensure compliance.

 

Installation de cet équipement doit être conformes aux codes électriques locaux et nationaux. Si nécessaire, consulter les organismes de réglementation appropriés et des autorités de contrôle pour assurer la conformité.

 

Important: Read all installation instructions before connecting the system to the power source.

 

Lire toutes les instructions d'installation avant de brancher le système à la source d'alimentation.

 

Most installations will have redundant, dual, independent power feeds. Each independent power feed will be referenced as A and B.

The recommended installation is to wire each supply to independent power feed (A or B).

Each power supply includes a fan that maintains proper power supply temperature. The following appendices display the location of the following component on all switches described in this guide.

Front Panel displays the front panel location of the supervisor modules and line cards.

Rear Panel displays the rear panel location of switch card modules (not visible), fans, and PSUs.

 

Important: This unit requires over-current protection.

 

Cet appareil nécessite de protection contre les surintensités.

 

Important: Unused slots must be occupied or covered with a blank to ensure proper airflow through the chassis.

 

Les emplacements inutilisés doivent être occupés ou recouvert d'un blanc pour assurer la bonne circulation d'air dans le châssis.

 

Connecting Supervisor Cables

Supervisor modules contain console, management, and USB ports. Figure 4 display port and status LED locations on the supervisors. Refer to the chassis specification in Connecting Supervisor Cables for additional information about the serial port.

Figure 4. Supervisor CCS-750-SUP100


1 Supervisor status LED 5 Switch card status LED 9 SFP and RJ-45 Ethernet management ports
2 Supervisor active status LED 6 Fan status LED 10 RJ-45 Serial management port
3 PSU status LED 7 Uplink status LED 11 USB Port
4 Linecard status LED 8 Supervisor/Uplink ports (2x QSFP100) 12 Release

 

Figure 5. Supervisor CCS-750-SUP25


1 Supervisor status LED 5 Switch card status LED 9 SFP and RJ-45 Ethernet management ports
2 Supervisor active status LED 6 Fan status LED 10 RJ-45 Serial management port
3 PSU status LED 7 Uplink status LED 11 USB Port
4 Linecard status LED 8 Supervisor/Uplink ports (4x SFP25) 12 Release

 

  • Console (Serial) Port: Connect to a PC with RJ-45 to DB-9 serial adapter cable. Default switch settings include:
    • 9600 baud
    • No flow control
    • 1 stop bit
    • No parity bits
    • 8 data bits

    The supervisor cards must be installed in one of the two slots designated for them. They are shown in Front Panel for the switches.

    Table 3. RJ-45 tp DB-9 Connections
    RJ-45 DB-9   RJ-45 DB-9
    RTS 1 8 CTS   GND 5 5 GND
    DTR 2 6 DSR   RXD 6 3 TXD
    TXD 3 2 RXD   DSR 7 4 DTR
    GND 4 5 GND   CTS 8 7 RTS

     

  • Ethernet management port: Connect to 10/100/1000 management network with RJ-45 cable.
  • USB Port: May be used for software or configuration updates.
  • Uplink Port: Use the relevant optics for connection.

Connecting Linecard Modules and Cables

Install required SFP, SFP+, QSFP+, QSFP100, OSFP, and QSFP-DD optic modules in linecard module ports Figure 6.

Figure 6. SFP or SFP+ Ports

Connect cables as required to linecard module ports. Supervisor and linecard module ejectors on the front of the chassis assist with cable management.

 

CAUTION: Excessive bending can damage interface cables, especially optical cables.

 

Flexion excessive peut endommager les câbles d'interface, en particulier les câbles optiques.

 

Note: You must ensure that any open slots for modules, supervisors, linecards, etc. are covered by the appropriate “blank” plates. Check with your local Arista Networks representative if you have questions.