Tag :: EOS 4.32.2F

The AGM for ECMP feature allows monitoring the number of packets and bytes going through each members of the configured ECMP groups on the system, with a high time resolution. Once enabled, the feature will collect data for the specified duration, write it to the specified files on the system’s storage, then stop.

BGP inbound update processing delay is a feature in EOS where an optional delay is applied prior to processing inbound UPDATE messages from a peer(s). The duration of the delay is configurable per peer. The delay is applied to UPDATE messages for all the address families that are negotiated with the peer. The delay timer starts when the peer becomes established. The routes from such peers are processed only after the timer expires. Any routes received after the timer expired are processed as usual without the delay. Both the default VRF and non-default VRFs are supported.

The feature allows to create a named TC to DSCP mapping that can be applied on an interface.DSCP of routed packets egressing out of the interface will be rewritten according to the map.

Filtered mirroring allows certain packets to be selected for mirroring, rather than all packets ingressing or egressing a mirror source port.

Forced periodic ARP refresh adds support for a mechanism that allows forcing ARP/NDP refresh requests to be sent in periodic intervals independently of ARP/NDP entries' confirmed time in the kernel. By default, when a neighbor entry gets confirmed by various processes such as ARP synchronization between MLAG peers, an ARP refresh request is not sent for at least another duration of ARP aging timeout (or ND cache expiry time for the IPv6 case). This feature provides support for a configuration to force sending refresh requests at the configured ARP/ND aging timeout regardless of the last confirmed time.

Normally, a switch traps L2 protocol frames to the CPU. However, certain use-cases may require these frames to be forwarded or dropped. And in cases where the L2 protocol frames are forwarded (eg: Pseudowire), we may require the frames to be trapped to the CPU or dropped. The L2 Protocol Forwarding feature provides a mechanism to control the behavior of L2 protocol frames received on a port or subinterface.

This feature allows users to configure L2 subinterfaces on MLAG interfaces. L2 subinterfaces are not supported on the MLAG peer-link.

The intended purpose of this feature is to introduce a server streaming RPC. When a client subscribes to this RPC, they will receive a message anytime there is an update to the hardware programming state of an MPLS route or the Nexthop-Group to which it points to. Note that messages will only be streamed in this RPC callback for versioned MPLS routes that point to versioned nexthop-groups. Messages will not be streamed via this RPC for MPLS routes and Nexthop-Groups that don’t meet this criteria.

This feature adds the support for OSPFv3 multi-site domains (currently this feature is added for IPv6 address family only) described in RFC6565 (OSPFv3 as a Provider to Customer Edge Protocol for BGP/MPLS IP Virtual Private Networks (VPNs) ) and enables routes BGP VPN routes to retain their original route type if they are in the same OSPFv3 domain. Two sites are considered to be in the same OSPFv3 domain if it is intended that routes from one site to the other be considered intra-network routes.

Configuration of arbitrary combinations of speeds on subinterfaces is being restricted on 800G CMIS Arista transceivers. This feature restricts configuring only uniform sets of speeds on applicable transceivers. This affects Arista-branded 800G active optical transceivers.

When this feature is enabled, responses to gNMI get requests as well as NETCONF get-config responses will contain the default values for YANG leafs if those leafs do not have any other value. This means that where a leaf value would normally be returned in a response, its default value (as defined in the YANG model) will be returned if the leaf does not have any other value assigned to it. Before this change, leafs that had a default value would not have been included in gNMI get responses.

Routing control functions (RCF) is a language that can be used to express route filtering and attribute modification logic in a powerful and programmatic fashion.

RSVP-TE P2MP LSR adds transit support for Point-to-Multipoint (P2MP) LSPs. Specifically the feature adds protocol support for the transit role as described in RFC 4875.

This document describes the support for performing SSH authentication with X.509 certificates. Authentication to SSH can be completed using a number of different methods. Public key, password and keyboard interactive are supported in EOS. Certificate login is a type of public key authentication in which the public key does not have to be stored on the server. Instead trusted certificate authorities are installed. A presented certificate must be signed either directly or indirectly by one of these trusted certificate authorities to allow authentication to the device. Support for OpenSSH certificates (also known as SSH Certificates) was added in 4.22.1F.

Prior to 4.32.2F, the “reset system storage secure” CLI command can be used to perform a best-effort storage device wipe of all sensitive data. However, this command has the limitation that it wipes EOS from the storage device, leaving the system “stuck” in Aboot. The “reset system storage secure rollback” command provides the same secure erase functionality, but additionally allows the user to preserve a subset of files on the main flash device by copying them into RAM during the secure erase procedure. The set of files that are preserved is configurable. After a successful wipe, the system will return to EOS after the erase is complete if the EOS SWI image and adequate configuration files are preserved (such as boot-config and startup-config).

IS-IS SR Stateful Switchover (SSO) support allows for a switchover from an active supervisor to a standby supervisor where MPLS traffic remains undisrupted during switchover. This involves reconciliation of all Segment Routing related information in the network using IS-IS Graceful Restart procedures. And also installing the same in forwarding hardware in a manner that does not disrupt the ongoing traffic.

In order to support PIM/IPv4 multicast routing on EOS switches with Broadcom Tomahawk4 ASICs, multicast support using ALPM is required. This works in both 3-level Algorithmic Longest Prefix Match (ALPM) capabilities and 2-level ALPM.

This document describes the availability of VLAN ingress and egress counters on R Series platforms. VLAN counters provide the ability to count packets and bytes ingressing or egressing a bridge domain (VLAN).