Status Indicators

The following topics are covered in this section:

Front Indicators

Reviews the Switch and Port Indicators of the device.

Switch Indicators

Locate the front panel LEDs on the right side of the chassis and display system, fan, and power supply status.

The front panel LEDs are labeled as System Status Indicators. They could be oriented horizontally on your switch.

Figure 1. System Status Indicators
1 System status LED 3 Power supply 1 status LED
2 Fan status LED 4 Power supply 2 status LED
Table 1. Switch Indicators LED States (Front)
LED Name LED State Device Status
System Status LED Blinking Green System is powering up.
Green Normal operations. Due to power supply and fan redundancy, this LED will remain green if a single fan or power supply is missing or in a failed state.
Blue The beacon (locator) function is active.
Amber Two or more fans (any combination of fan modules or PSU fans) are disconnected or malfunctioning. The switch will automatically execute a “graceful shutdown” shortly.
Fan Status LED Green All fan and power modules are operating normally.
Amber The single fan module is removed or malfunctioning. It is also amber when a PSU is completely removed or has a stuck fan rotor.
Red Two or more fans (any combination of fan modules or PSU fans) are disconnected or malfunctioning. The switch will automatically execute a “graceful shutdown” shortly.
PSU [1:2] Status LED Green PSU is functioning and fully operational. AC is present, Aux output is ON, and Main output is ON.
Off PSU has been removed or is not operating properly due to the AC cord being unplugged, its fan rotor being stuck, or an internal fault.

Port Indicators

Port LEDs near their corresponding ports provide link and operational status.

The following figure displays the Port LED location on the DCS-7050QX-32S switch.

Figure 2. Port LEDs

1 Port 4 LEDs 3 Port 2 LEDs
2 Port 3 LEDs 4 Port 1 LEDs

Table 2 provides status conditions corresponding to port LED states. Port LED behavior for QSFP+ and SFP+ ports is consistent.

Table 2. Port LED States (Front)
LED State Status
Off The port link is down.
Green The port link is up.
Yellow The port is software disabled.
Flashing Yellow The port failed diagnostics.

Rear Status Indicators

Fan and power supply modules are accessed from the rear panel.

Each fan and power supply module contains an LED that reports the module status.

Fan Status LEDs are on the fan modules, as displayed in Figure 3.

Figure 3. Fan Status LED

1 Fan module status LED

Fan Status LED States (Rear) provide conditions corresponding to fan status LED states.

Table 3. Fan Status LED States (Rear)
LED State Status
Off The fan module is not detected. If it is inserted, it may not be seated properly.
Green The fan is operating normally. This LED state is exclusive to its fan module and independent of the states of its neighboring fans and power supplies.
Red The fan has failed.

The AC Power Supply Status LEDs are on the power supply modules, as displayed in Figure 4. Depending on the power supply, the LED could be in a different location on the PSU.

Figure 4. AC Power Supply Status LED

1 Power supply status LED

AC Power Supply Status LED States (Rear) provides conditions corresponding to the AC power supply status LED states.

Table 4. AC Power Supply Status LED States (Rear)
Power Supply State PWR-1011-AC PWR-1511-AC PWR-2411-AC
Input power present Normal operation Green Green Green
Input power present Power Supply fault Yellow Yellow Yellow
No Input Power Supply is installed in the chassis Off Off Off
Input power present Supply not installed in chassis Green Green Green

The DC Power Supply Status LEDs are on the modules, as displayed in the DC Power Supply Status LED.

Figure 5. DC Power Supply Status LED
1 Power supply status LED

DC Power Supply Status LED States (Rear) provides conditions corresponding to the DC power supply status LED states.

Table 5. DC Power Supply Status LED States (Rear)
Power Supply State PWR-1011-DC PWR-1511-DC PWR-2411-DC
Input power present Normal operation Green Green Green
Input power present Power Supply fault Blinking Yellow Blinking Yellow Blinking Yellow
No Input Power Supply is installed in the chassis Off Off Off
Input power present Supply not installed in chassis Blinking Yellow Blinking Yellow Blinking Yellow
Note: You can narrow the error condition by logging in to the switch to view the specific device state. Refer to the Arista User Manual’s Switch Environment Control chapter under Viewing Environment Status for further information on the show environment commands.